PRODUCT TESTING

Test report for 80347

Brushed Nickel · 128 mm hole centers

Review the recorded test conditions and results for this submitted cabinet pull sample, alongside the complete laboratory report.

Applies to the submitted sample identified below.

Product image of the 80347 Brushed Nickel 128 mm cabinet pull.
Product image for identification. See page 6 of the report for the submitted sample photograph.

Modified salt spray

120 hours

NaCl 10 g/L · Rp 10 · Ra 10

Separate cross-cut test

Class 0

ISO 2409:2020

Report conclusion

DATA

Results recorded without a pass/fail statement.

01 / SAMPLE

The submitted sample

The report identifies a zinc alloy hardware handle with a Brushed Nickel electroplated finish, model 80347, with 128 mm hole centers.

Material and finish descriptions identify the sample. This report does not establish the alloy composition of other products.

Model
80347
Declared base material
Zinc alloy
Finish
Brushed Nickel, electroplated
Hole centers
128 mm
Manufacturer named in report
FANXIN HARDWARE CO., LTD

02 / METHODS

Methods and conditions

TEST 01

Modified salt spray test

ISO 9227:2022, modified to use NaCl at 10 g/L.

  • NaCl concentration: 10 g/L (described as 1% in the report summary).
  • Exposure: 120 hours
  • pH: 6.5–7.2
  • Chamber temperature: 33–37°C

Corrosion ratings referenced to EN ISO 10289:2001.

Rp 10 is the recorded protection rating; Ra 10 is the recorded appearance rating. The report's rating table assigns 10 where no defects are observed in the evaluated area.

Source: report page 3.

TEST 02

Cross-cut test

ISO 2409:2020. Recorded classification: Class 0.

The report describes Class 0 as smooth cut edges with none of the lattice squares detached.

The laboratory clarified by email that the tested layer was the transparent protective surface layer.

The cross-cut and salt spray tests were submitted separately. Class 0 is not presented as a result after salt spray exposure.

Source: report page 5; tested-layer clarification from laboratory correspondence.

03 / SOURCE DOCUMENT

Read the original report

The six-page PDF below is the complete report as supplied by the laboratory. The explanations on this webpage are KHTUMEWARE summaries; the original report remains the source document.

Cover of report (6626)258-1313 Revised for model 80347, Brushed Nickel, 128 mm.
Report cover. The full PDF contains all six pages.

Report number: (6626)258-1313 Revised
Laboratory: Bureau Veritas
Original report date: September 24, 2026
Revised: October 15, 2026

If the preview is unavailable, open the PDF in a new tab or download the full report.

For easier reading on your phone, open the PDF in a new tab. Your browser controls zooming and saving.

Scope of this report

These results relate only to the submitted sample and the methods and conditions stated in the report. They do not establish performance for every product, finish, size, batch or installation.

The 120-hour salt spray exposure is a laboratory test duration. It is not a stated service life or an outdoor-use rating.

The report records DATA for both tests. This webpage presents those observations without adding a certification or pass/fail claim.

This report does not establish compliance with a project specification or acceptance criteria. Confirm any required method, concentration, duration and acceptance criteria before ordering.

Retail pack quantities and business carton quantities are separate commercial details. This report does not verify packaging quantities or terms of supply.

Retail and business options

For a U.S. retail purchase, review the selected size, finish and pack on the product page.

For business supply, confirm the exact item and required test specification with our team. Quantity, packaging and supply terms are reviewed separately.

Questions about this model or another specification

Send the product link, finish and hole centers so we can check the available documentation. Business buyers can also include quantity, destination and any required test specification.

Ask about product documentation